EZPoxy EZClean Sand/Colorant + Resin Kit - 14 lbs
Click to enlarge

EZPoxy EZClean Sand/Colorant + Resin Kit - 14 lbs

MFR: Bostik Smart Adhesives
Product ID : ASBO4000E
Price: $232.92

Purchase

E-mail to a friend

Description

Bostik EzPoxy™ EzClean™ is a 100% Solids Epoxy Mortar & Grout with outstanding application and clean-up properties. Use with ceramic, quarry, porcelain, granite, slate, pre-cast terrazzo, dimensional and moisture-sensitive stone tiles over properly prepared concrete, structurally sound, exterior grade plywood (interior/dry use only), cement backer board, Bostik GoldPlus™ and existing ceramic tile. EZPoxy™ EZClean™ has been formulated with an advanced binder system which offers superior thermal shock resistance and remarkable ease of initial clean-up. For use in grout joints from 1/16" to 1/2".


DIRECTIONS FOR USE

Read and understand technical and safety data sheets completely before beginning installations. Refer to Bostik Technical Data Sheet for product information.


WHEN USED AS A MORTAR

SURFACE PREPARATION

All surfaces must be structurally sound, dimensionally stable, dry, clean and free from all contaminants. For best results, surface, mortar, and tile should be at room temperature (70°F/21°C to 75°F/24°C). Do not apply at temperatures below 60°F (16°C), or above 85°F (29°C). Epoxy materials are affected by temperature variations. Cooler temperatures will decrease
workability. Warmer temperatures will reduce sag resistance.

MIXING
Pour the entire contents of Part A and Part B into the 3.5-gallon pail. Mix for approximately 40 seconds. Then add the sand/ colorant packet and mix for approximately 1 additional minute.

Immediately pour product onto cool substrate to extend working time. 


WHEN USED AS A GROUTING SYSTEM

SURFACE PREPARATION

Ensure tile is firmly set and mortar completely dry before grouting. Remove all spacers, debris or adhesive from tile joints. Application of a grout release agent may be necessary to prevent staining of tile. For best results, surface of tile should be at room temperature (70°F/21°C to 75°F/24°C). Do not apply at temperatures below 60°F (16°C), or above 85°F (29°C).

Epoxy materials are affected by temperature variations. Cooler temperatures will decrease workability. Warmer temperatures will reduce sag resistance.

APPLICATION
GROUT: Lightly moisten tile with clean, damp sponge before grouting. Spread grout over the face of the tile using a hard rubber epoxy grout float. Work grout back and forth at a 45° angle to the face of the tile to ensure complete filling of the joints. Remove excess grout by holding the rubber float at a
90° angle working diagonally across face of the tile.

LIMITATIONS

• All epoxies are temperature sensitive. Temperature swings 10°F (-12°C) up or down from 70°F (21°C) will impact the product’s viscosity and workability.
• Epoxies may discolor when exposed to ultra-violet light. It is less noticeable with darker colors.

  • EzPoxy™ EzClean™ 100% Solids Epoxy Mortar & Grout may show discoloration when exposed to strong chemicals, high temperatures, and/or staining materials for long periods of time. Wipe spills promptly.
    • Do not use in installations where deflection exceeds L/360 (1" in 30 feet).
  • Do not mix partial units.
  • Do not apply over oriented strand board, particle board, masonite, luaun, or similar unstable substrates.
  • Do not use where hydrostatic pressure can occur.
  • Due to the limitations of plywood as a substrate, EzPoxy™ EzClean™ 100% Solids Epoxy Mortar & Grout is not intended for use on plywood in exterior, wet interior, or applications subject to heavy/commercial traffic.
    • Intermittent exposure to temperatures up to 350°F (176.6°C) is acceptable. Not for continuous exposure to temperatures above 140°F (60°C). May stain light colored marble or stone.
  • Do not use as an adhesive/mortar for exterior installations.
  • Trowel size is suggested to maximize transfer/coverage of mortar. Periodically check coverage during installation.


MATERIALS

  • Ceramic 
  • Quarry
  • Porcelain
  • Granite
  • Slate
  • Pre-cast terrazzo
  • Dimensional and moisture sensitive tiles 


PACKAGING 

Resin Kit 
Part A (Resin) - 48 fl oz (1.41 L) 
Part B (Hardener) - 11.7 fl oz (340 mL) 

Sand/Colorant - 11 lbs (5.0 kg)


TAKE NOTE

* Free Shipping
* Orders of EZPoxy EZClean take 4 to 6 business days to deliver.

Product Reviews

Login or Register to write the first review.